Gunpower/Airforce

Luxfer 1 Ltr 300BAR Carbon Fiber Wrapped Composite Cylinder with Extreme-Flow Valve with Assemb..

Available Options * Valve Assembly:  High Flow Valve Assembly without Internals. (Swap..

Available Options * Valve Assembly: High Flow Valve Assembly without Internals. (Swap Inter..

Barrel bushings for .22 and .25 cal barrels which have and Outer Diameter of 16mm. Comes with gru..

Barrel bushings for .257 cal barrels which have and Outer Diameter of 14.2mm. Comes with gru..

Airforce Barrel Guided End Cap This custom machined metal end cap ..

Airforce Barrel Guided End Cap This custom machined metal end cap has been designed to close fit an..

Airforce Brass Spring Retainers for the .22 and .25 valves Contact us if you need any further cus..

Airforce Brass Valve Guide. Comes with o-ring pre-lubed with silicon grease and installed. Con..

Specifications : Burst Disk rated 3K with brass body. These burst disk are meant for the ..

Specifications : Burst Disk 5K with Steel Body has a 5000 PSI Burst Disc Installed. This is fo..

Airforce Butt Plate Assembly Those who are looking for a spare Airforce Butt Plate Assembly for t..

https://www.pcpshop.in/airforce-condor-regulator-adjust-regulated-pressure-assembly.html Airforce..

Airforce Condor Valve Spring for .177 Contact us if you need any further customization and we sha..

Airforce Condor Valve Spring for .22 and .25 cal Contact us if you need any further customization..

Airforce Delrin Base Seat which is installed after removing the brass valve guide. The delrin bas..

Extreme-Flow Valve Assembly Spring to be used with heavier hammer and custom sturdier one piece valv..

The Airforce Fluted Breech Ver 2 replaces the Airfoce Standard Breech. Made from higher grade of ..

Airforce Grip Nut and Locking Bolt for those seeking replacement parts. Contact us if you need an..

Airforce Gunpower Factory Hammer Spring Replacement part for factory hammer spring. Contact us..

There has been an upgrade to the finish, we just added a chrome finish to the 70 grams brass hammer...

Airforce O Rings Kit comprises of the below which will help refurbish your airgun and air tank as ne..

Airforce / Gunpower Power Wheel SS Screw These replace the plastic screw on the power wheel and a..

Specifications: AirForce Refill Adapter made out of SS or Brass with BSP Threads. Made from Prem..

Specifications: AirForce Refill Adapter made out of SS with Male Foster Fill Made from Premium Q..

Airforce Safety Lever Knob Replacement knob for those who have lost the safety lever red sleeve. ..

Airforce Standard Angled Tank Adapter for 400cc and 500cc Cylinders These Angled adpaters will gi..

Airforce Texan Regulator with Dual Gauge V1 (First of its Kind for the Airforce and Gunpower Big Bor..

Protect your Airforce Texan Tank Valve from dust/dirt build up in the air flow valve! Now ..

Airforce Trigger Assembly springs comprises of a set of 4 springs. These are for the older models..

Airforce Trigger Assembly springs comprises of a set of 4 springs. These are for the newer models..

Airforce/Gunpower Custom Metal Trigger Shoe is a recommended upgrade from the plastic trigger s..

Airforce/Gunpower End Cap Adapter for additional Shroud/Moderator This custom mac..

Airforce/Gunpower Texan O-Rings Kit comprises of the below o rings which will help refurbish your ai..

Airforce/Gunpower Valve assembly NPT Dead End Plugs Looking to shut the ports where the gauge and..

Airforce/Gunpower Valve Removal Tool​  This tool was designed to help customers remove the v..

Must have tool if you like to run maintenance or upgrade your valves on the airforce or gunpower tan..

Extension Adapter for Extreme-Flow Valve Ver 2 was machined for our customers who wanted to have Gau..

Extension Adapter for TalonP Cylinder was designed for customers who seek an easier method to backpa..

Extra Heavy Brass Hammer (114 g) Ver3 This custom extra heavy brass hammer is to be used in conju..

Extra Heavy Brass Hammer (115 g) Ver2 for Newer Version Condors and Older Version Condors. T..

Extra Heavy Steel Hammer (109 g) Ver3 for Newer Version Condors and Older Version Condors. T..

Extra Heavy Steel Hammer (110 g) Ver2 for Newer Version Condors and Older Version Condors. T..

Extreme-Flow Valve with Assembly Kit comprise of our custom PCP Tunes Extreme-Flow Valve, for those ..

The custom fluted breech replaces the Airfoce Standard Breech. Made from higher grade of delrin w..

The above custom heavy brass hammer with custom delrin anti-friction guides weigh 70 grams and repla..

Used in Conjunction with custom condor valve ! The custom heavy brass hammer is used in conjuncti..

The above custom heavy steel hammer with custom delrin anti-friction guides weigh 68 grams and repla..

Used in Conjunction with custom condor valve ! The custom heavy steel hammer is used in conjuncti..

Hi Flow Valve with ETAC Adapter for CANT and Valve Protect Cap For those who have been looking fo..

The custom one piece Hi-Flow valve is used in conjunction with custom heavy steel/brass hammer for m..

Hi-Flow Valve with Assembly comprise of our custom PCP Tunes Valve, helps increase the output and pr..

"Hi-Flow Valve with Assembly" comprise of our custom PCP Tunes Valve, helps increase the output and ..

The custom breech knob replaces the MS hollow knob with rubber cover which screws onto the breech of..

The custom one piece high performance valve for gunpower UK 12 fpe version is made from durable..

Spin-Loc Conversion Kit are the answer for those seeking an upgrade from the older version..

Mini Cylinder "Buddy Bottle" 480cc 200BAR Maximum Working Pressure. No Valve M18 x 1.5 Thread ..

Super Sear Ver1 for Older version Condor frames.     ..

Super Sear Ver2 (Newer Models Condor Only)     ..

Talon Tunes TTTA Z adapter CANT with gauge and fill nipple. This angled adapter is for those who ..

TalonP valve to Condor Tank Adapter We now have a solution for those who were looking for larger ..

Protect your air tank from dust/dirt build up in the air flow valve! Now even more lighter. The c..

Wok Butt Plate for Airforce Airguns Many who do not like the fit of the factory butt plate on the..